2N 2N 2N Units. Collector – Emitter Voltage. VCEO. . verify that the information in this data sheet is current before using this product. Visit for additional data sheets and product information. Forward Current Transfer Ratio. IC = 10 Adc, VCE = 3 Vdc. 2N 2N NPN POWER SILICON TRANSISTOR. Qualified per MIL-PRF/ T4- LDS Rev. 1 (). Page 1 of 5. DEVICES. LEVELS. 2N 2N
|Published (Last):||10 February 2015|
|PDF File Size:||11.93 Mb|
|ePub File Size:||2.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
Each circuit diagram has component values for a particular voltage and current regulator design. Second Significant Figure C? If you look up the house number and find the recommended replacement part, you can often find other standard parts that are replaced by that same part.
The current limit adjust is set for a maximum output current of 85 amperes. CRCW Series 0. An Aiternate Method of Sensing Line Fauit and Overvoitage Conditions for Linear Datasyeet Suppiies and medium sized computer systems which must store part or n26249 of the data currently being processed before the power failure.
Each circuit has a practical power range or capability associated with it as follows: Depending on which regulator type is used, this config- uration can provide output currents in excess of 3A. Output Current Boosting If output currents greater than those available from the basic circuit configura- tions are desired, the current boost circuits shown in this section can be used. However, the same considerations apply for pass elements used with negative regulators.
Each device is protected from excessive switching voltage spikes by an R-C snubber, and output current sharing is aided by having separate secondary windings. Each particular sampling plan will have its own O.
All standard resistance values, from less than 1? However, the flyback regulators which evolved from this configuration deliver only the inductive energy stored in the choke to the load. R2 is therefore chosen to consist of a 62K resistor and a 2K trimpot. If the primary hangs over an extra half layer, try reducing dtaasheet turns or the wire size.
2N 데이터시트(PDF) – Central Semiconductor Corp
In these cases, a clamp diode should be connected to the regulator output as shown in Figure 2n629. The fanout of a replacement should be equal to, or greater than, that required in the circuit. Less output current 2h6249 now required to keep Va and Vr2 at a level sufficient to bias Q3 on since the voltage at its emitter has the tendency to decrease faster than that at its base. The following paragraphs provide useful information and performance results regarding this Flyback design.
Wakefield, MA 2.
2N Datasheet pdf – NPN SILICON TRANSISTOR – Central Semiconductor
Device Two columns are provided listing Motorola part numbers for positive and negative voltage outputs. Oth- erwise, the power supply, across which the SCR dataeheet connected, must be shut down to reset the crowbar. Inside Diameter Typeor 0.
The circuit shown in Figure senses the voltage datashwet the power supply filter capacitors to predict the imminent power supply failure. Black on White Material: These are instantaneous values. Closer matching of the internal amplifier input transistors, minimizes this effect, as does selecting a feedback ratio, j8, to be close to unity. If a replacement IC uses much more current than the device it replaces, a heat sink or blower may be needed to keep it cool.
This is accomplished by providing a separate low voltage input supply for the pass element. C3 and C4 may be increased to Improve load transient response and to reduce the output noise voltage. Dual Overvoltage Protection — The circuit shown in Figure uses the MC to provide overvoltage sensing for a split supply.
This is satisfactory for most analysis work, and only the transformer turns ratio will have to be adjusted slightly to compensate for IR drops, diode drops, and transistor saturation voltages. Ferrite cores are not typically datashset, so identification is more difficult.
However, the output also depends on the load which was not the case with buck regulators and results in a variation of loop gain with load. In order to obtain the greatest output voltage compliance range at a given input voltage, the MC or MC79L03 should be used in this configuration.
Other characteristics such as static regulation specs are comparable, while ripple and load transient response are usually worse. S 10, Input C pF 4 5 5 datasneet This method, however, usually ne- cessitates that separate short circuit protection be provided for the IC regulator and external pass element.
2N6249 Datasheet PDF
Current Regulator The three terminal negative regulators may also be used to provide a constant current sink, as shown in Figure D. However, this method presents a basic problem to the regulator designer. If the secondary of the IF transformer is center-tapped, the second diode plate lead is greenand-black dtaasheet, and black is used for the center-tap lead. Custom Heat Sink Design Custom heatsinks are usually either forced air cooled or convection cooled.
For example, a resistor as shown in Fig Q12 will inhibit the 2n2649 until the ac line is disconnected. First, a trial heatsink is chosen: Since the base-emitter junction drops of Q1 and Rsc have been added to the circuit, they must be added to the minimum value of Vin — Vo. These limits are instantaneous values, not catasheet.