Smith Meter® AccuLoad and AccuLoad III are trademarks of FMC The default or operating values used in this manual and in the program of the AccuLoad III. AccuLoad III High Speed Prover Output · AccuLoad III Vapor Recovery Application Bulletin · AccuLoad IIInet Application Manual · AccuLoad III-S N4 Hardware. The default or operating values used in this manual and in the program of the Smith Table of Contents iii. Volume Accuracy – Preset Amount Type.
|Published (Last):||6 January 2008|
|PDF File Size:||15.12 Mb|
|ePub File Size:||2.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
This feature is intended to be used in applications where it is desired to continuously blend two or more products where a preset volume is not normally used. See Installation Manual MN for additional details. Volumetric correction is calculated directly from published API equations providing precise volumetric measurement results. Safety accullad volume accuracy functions including excess high flow, low flow, overrun, and temperature probe failure are also monitored per their program parameters.
It is suggested the backup battery be replaced approximately every. Type the abstract of the document here. In any case, transaction records should be downloaded for archival purposes if required by local agencies as.
System Program Code determines the period during which mqnual AccuLoad remains in a full screen format.
Accuload iii manual español – Google Docs
After the prove is complete, the operator enters the prover volume and prover temperature and the AccuLoad calculates the new meter factor. An alarm will be set if the number of errors exceeds the programmable maximum. This interface offers the potential for enhanced functionality and manuxl ranging from simple transaction-stamping with driver card data to a mini automation system with validation and authorization.
The AccuLoad provides a vapor product total and a net mass total between the liquid product meter and the vapor product meter in the system.
This is most commonly done with products that mix very mznual. The AccuLoad controls the flow of the additive in an attempt to constantly maintain the desired ratio as if the additive were a ratio product.
Remove all items from the box and make sure the. Step 1 Download App on your mobile device.
The operation is as follows for manual selection of additives: The ratio of varying products is designated in the recipe as a percentage of the total preset. To initiate the proving sequence, the AccuLoad will prompt for the prover coefficient of cubical expansion.
Smith Meter AccuLoad III – PDF
Coordinated to the flowmeters and their More information. User s Manual for Fingerprint Door Control Software Foreword The naissance of F7 indicated that fingerprint reader enters into professional door control domain. Remove all items from the box and make sure the More information. However, as a precau. The Reference section gives a description of each program code available in the ,anual.
404 page not found
Select recipe gdiesel-r Diesel-C Unleaded More Software Manual Contents 1 Software Installation The life of the battery used for the backup RAM can vary due to operational conditions, particularly the amount of. If set to zero seconds, zoom is prohibited. Refer to Installation Manual MN for wiring and programming information. The operator must next select the meter factor and associated flow rate for proving.
Coordinated to the flowmeters and their. To facilitate replacement of this battery, the KDC board must be removed. When the batch has completed, the AccuLoad will prompt for the actual prover volume. You can access these features by selecting the items under. When the operator enters the preset, the AccuLoad automatically calculates the actual volumes of each product to be delivered. Don’t show me this message again. On a hybrid arm there must be at least one sequential product configured.
The AccuLoad III is also capable of maintaining back pressure on the measurement system using either automatic flow optimization or a pressure transmitter.
Got it, continue to print. F2 does not function while the Main Menu or any of its submenus is being displayed, or when the Dynamic Displays are being navigated. Product delivery is controlled by several program code entries. Precise temperature, pressure compensation, and density correction are options that are available in the instrument.
After Additive Injector 1 has been selected to either ON or OFF, press the down arrow key and continue selection with the next injector. Converters 1 Contents Overview and Features Delivery screens are similar to those shown below, whether the load arm is a single preset, a sequential blender, or a ratio blender. Also provided More information. Page of 94 Go. Each of these is delivered as a type of mini-batch, complete with individual high flow rates, first trip volumes, and so on.
They operate independently and can be configured to close on a Valve Fault, on any alarm, or not at all. By pressing ‘print’ button you will print only current page. The ratio product s can be plumbed either upstream or down stream of the sequential product meter. When selected as general purpose inputs and outputs, they provide 20 additional DC inputs and 40 additional AC outputs.