Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: Gurn Mezisar
Country: Eritrea
Language: English (Spanish)
Genre: Travel
Published (Last): 14 March 2005
Pages: 301
PDF File Size: 10.94 Mb
ePub File Size: 20.83 Mb
ISBN: 562-9-53473-219-6
Downloads: 62769
Price: Free* [*Free Regsitration Required]
Uploader: Tojaramar

Such requirements may include, 4a93 are not limited to the following: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. General Requirements for Delivery 4. ICS Number Code The producer should be consulted when material is required to tensile strength ranges other than those specied. Historical Version s – view previous versions of standard. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

The following coatings may be specied: The material shall also conform to the requirements as to mechanical properties. This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor.

  LIBROS DE QUIROPRACTICA PDF

ASTM A493 – 16

A number in parentheses indicates the year of last reapproval. The following lubricants may be specied: The SI equivalents are in parentheses and may aetm approximate. Soap is generally used.

Last previous edition A — Copyright ASTM Standard Astj for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

NOTE 1—A typical ordering description is as follows: All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. This abstract is satm brief summary of the referenced standard.

For smaller sizes, similar mechanical properties apply to ferritic and martensitic grades; however the producer should be consulted regarding somewhat higher tensile properties applicable to austenitic grades. B Product analysis tolerance over the maximum limit for carbon and nitrogen to be 0.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Originally published as A — Material satm be manufactured to tensile strength ranges other than those shown in Table 2. Link to Active This link will always route to the current Active version of the standard.

  74HC04AP DATASHEET PDF

The aetm given atsm parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. This standard has been approved for use by agencies of the Department of Defense. Resistance to Intergranular Corrosion 8.

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

An electroplated copper coating is often used. Current edition approved Jan.

The steel shall conform to the required aastm composition requirements. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

Packaging and Package Marking 9.

Last modified: January 26, 2020