EUROMAP 70 Electrical Interface between Injection Moulding Views. 6 years ago. Euromap, · Electrical, · Interface, · Injection, · Moulding. Euromap 2: Mould Fixing Dimension for Injection Moulding Machines. Specific information .. Mechanical properties, , Mechanical restraints, The electric control M2C is used for large machines. – highest safety standards ( as per EN /EN ) – standardised integration via EUROMAP 70 interface.

Author: Morg Nikoshakar
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Photos
Published (Last): 19 November 2009
Pages: 488
PDF File Size: 19.41 Mb
ePub File Size: 12.78 Mb
ISBN: 878-7-79280-425-1
Downloads: 97556
Price: Free* [*Free Regsitration Required]
Uploader: Kiganos

The signals are conducted from the signal source to the respective pin.

Functional principle and interface of the magnetic clamping system: The electric control M2C is used for large machines. Combinations with Hilma machine vices or Stark zero point clamping systems can be easily realised, as they all come from a single supplier.

Clamping and unclamping of several dies at the euromp time within a second. Figure 6 Magnetic clamping system in a rubber moulding press of the company Wickert Plate size xmm, magnetic force up to kN possible.

A current of at least 6 mA must be maintained eurommap signalling The maximum current is 1A Logical Signals 2. The electric control M1C is used for small and medium-sized machines. Pin d2 18 — 36V DC max. The system itself does not have any movable elements and is practically maintenance-free.

Magnetic clamping systems for deformation tools

All signals which are not optional shall be supported by all injection moulding machines and magnetic clamping systems. Plug on the injection moulding machine male. A permanent monitoring of the clamping condition, the temperature, and the position of the die by a eromap, separate control offers the maximum possible safety for automated processes. Rotary table with magnetic plate.

  BIOENERGETICS LOWEN PDF

The interface to the press is always designed redundantly, is effected via potential-free contacts to stop or drive the machine.

A further supplier added v. During the whole machining process, the control continuously monitors the parameters of the magnetic force, the position of the die die contact and the temperature. This penetrates only a few millimetres into the die base plate and will therefore have no impact on the die and the products.

Technical Recommendations | EUROMAP – European Plastics and Rubber Machinery

It is suitable for fitting or retrofitting without any problems in nearly all presses. An indicator light on the remote control continuously shows the state of the system.

In addition recommendations are given for signal voltage and current levels. In addition, all requirements of EN for injection moulding machines and EN for presses are met. M-TECS function principle for vertical design. Quick die change on presses and automatic punching machines. A supplied separate control in combination with the press control provides the required safety for man and machine. Figure 10 Magnetic clamping system installed in Arburg C High concentration effect of the magnetic force close to the centring ring.

The magnetic clamping systems or clamping plates have been especially designed for injection moulding machines, rubber presses, die casting machines, mould carrier and presses for metal forming. Die or mould change on punches and presses within a few minutes as well as further processing advantages are created with Hilma magnetic clamping systems.

Figure 7 Magnetic clamping system in a rubber moulding press of the company PanStone Plate size xmm, magnetic force kN realised for small and medium mould weights. M-TECS function principle for horizontal design.

The magnetic force is generated in a very flat, highly concentrated magnetic field. The forces can be adapted upwards and downwards to the needs of the machine.

  BILL EDWARDS FRETBOARD LOGIC PDF

Figure 9 Long pole technology in a to injection moulding machine Closure force: All signals are continuous signals unless otherwise noted. Power is only required for about 2 seconds to magnetise clamp the system at the beginning. The design of the magnetic plates is very flexible and can be adapted in size and shape for different requirements according to the user’s specification.

Only to unclamp the die, electrical energy is required again. Magnetic clamping systems especially designed for mould carrier machines. The mains supply of the MCS is also specified. The fixation is made in an all around clamping groove by means of clamping claws. The mould halves are heated by the magnetic heating plate.

Technical Recommendations

The contact making is either potential-free or related to a reference potential supplied euromao a contact of the plug mounted on the injection moulding machine or the magnetic clamping system see Tables 1 and 2.

Vertical arrangement with high safety requirements. With the smallest movement of a die half, the machine will be stopped guaranteed safety for man and machine. Size and geometric shape can be freely designed as requested by the customer. In operation, the system works independently of any power supply.

Figure 12 Magnet clamping system for an injection moulding machine of the company Ferromatic Closure force: The plate thicknesses are between 75 mm.

Safety of the magnetic clamping system: Pin a2 and Table 2: Magnetic clamping plates for different sectors of industry as e.

Last modified: January 4, 2020