View and Download Kurzweil PC3 musician’s manual online. Kurzweil PC3: User Guide. PC3 Electronic Keyboard pdf manual download. Also for: Pc3x. View and Download Kurzweil PC3x service manual online. PC3x Synthesizer pdf manual download. Kurzweil®, and PC3® are trademarks of Young Chang Co., Ltd. All other products and brand names are trademarks or registered trademarks of their respective.

Author: Mikree Dakus
Country: Yemen
Language: English (Spanish)
Genre: History
Published (Last): 13 September 2008
Pages: 28
PDF File Size: 13.18 Mb
ePub File Size: 18.37 Mb
ISBN: 169-1-89642-714-2
Downloads: 40898
Price: Free* [*Free Regsitration Required]
Uploader: Garn

Don’t have an account? Description of Tests Sine Wave Test For a pure sine wave that exercises the full dynamic range of the PC3x, press the Run PC3 soft button to exit diagnostics and return to normal operation.

Be sure the blue xD Daughtercard bezel is seated in the rear panel cutout properly. See Cp3 3, Page For instructions, refer to the Boot Loader in Chapter 4, page Page 77 Many, but not all, PC3 sample roots have been pre-assigned a carefully chosen, fixed alternate sample start or end point that can be selected using the Alternate Switch feature altControl and altMethod parameters.

Power Problems If a unit set for V is plugged into V, the fuses will blow immediately but no damage should occur to the unit.


PC3 or higher 2. Once the PC3x is on and ready to play, simultaneously hold down the 4, 5 and 6 buttons.

Remove the eight screws that secure the Connector Board to the rear panel. Majual the key from the pivot anchoring the key to the keyboard chassis. Follow the procedure described on page to remove the Connector Board. Note Start the sample will begin at the pre-set alternate start point in this manyal, slightly past the initial chiff.


In Program mode, use the numeric keypad and select programSine Wave. Page 23 Diagnostics Description of Tests Notes 1. Page of Go. Turn the power off and remove the power cord.

Do not remove the endcap or rear panel screws at this point of the procedure.

Kurzweil Music Systems – PC3X – PC3 Series Musician’s Guide

Also See for PC3x Musician’s manual – pages Getting started manual – pages Getting started manual – ukrzweil. Page and Program Buttons Removing the Battery The battery CR in the PC3x keyboard is mounted into a holder on the Engine Board and is accessible when the access panel is removed. What module do you want to update? Connect the stranded wire cable from the Transformer to J px3 the Connector Board.

Remove the four screws that kurzwekl the two PC board clamps two screws per clamp. Be sure that the rubber key contacts line up properly through the holes in the keyboard chassis. Do not block any of the ventilation openings.

The PC3x should boot up normally. Table of Contents Add to my manuals Add.

Kurzweil PC3 Musician’s Manual

The rear panel screws secure the lip. The next PCH in the the newly selected bank. Remove the seven screws that secure the access panel and set it safely aside. If you use 5 mm X 20 mm fuses, install them toward the inside end of the fuse holder near the metal pins. Many, but not all, PC3 sample roots have been pre-assigned a carefully chosen, fixed alternate sample start or end point that can be selected using the Alternate Switch feature altControl and altMethod parameters. Refer to Figure for the position of the screws.

If you are merely replacing one or more keys, it is not necessary to entirely remove the keyboard from the PC3x. Wheels Assembly to the bottom enclosure. There are three main sections: However, to avoid reversing the Bass and Treble cables when reconnecting, mark one or both cables designating B for Bass and T for Treble.


Lower the key into position. Clean only with dry cloth. By pressing ‘print’ button you will print only current page. Place the LCD Board in position face down onto the front panel bezel. Follow the procedure described on page to remove the enclosure support wall. Chapter 1 Introduction This chapter provides the service technician with a layout of the front and rear panel features, as well as a brief explanation of their functions.

Comments to this Manuals Your Name.

Each endcap includes the endcap, endcap side bracket and endcap locking bracket. If the service you are performing only requires that you have access to the Front Panel Board for component testing or component kuzweil, it is not necessary to separate the LCD Board from Front Panel Board.

Removing the top enclosure requires removing the left and right endcaps.

PC3x bottom enclosure Caution: Card or the USB port via computer. Front Panel Problems 4. Edit button—use this mxnual to enter the editor or the current mode to modify a selected object or parameter. Diagnostics Diagnostic Test Modes Diagnostic Test Modes The run test mode allows you to select an individual test, or to step through and run each available test.

These screws also secure the rear panel edge of the Board. Updating Via Computer If you have not completed these steps, do so before continuing.

Last modified: December 27, 2019